• Welcome to The Truck Stop! We see you haven't REGISTERED yet.

    Your truck knowledge is missing!
    • Registration is FREE , all we need is your birthday and email. (We don't share ANY data with ANYONE)
    • We have tons of knowledge here for your diesel truck!
    • Post your own topics and reply to existing threads to help others out!
    • NO ADS! The site is fully functional and ad free!
    CLICK HERE TO REGISTER!

    Problems registering? Click here to contact us!

    Already registered, but need a PASSWORD RESET? CLICK HERE TO RESET YOUR PASSWORD!

Engine cuts out in reverse

G

Goose57

Well-Known Member
Messages
275
Reaction score
699
Location
Eureka Mo.
Hi all, I just got done w/ a new Optimizer build on my 95’ Duelly. It just started to cut out when backing up. Just a hiccup always in reverse. Never in drive. One time it did shut off. New 5521 IP, LP, known working PMD behind bumper, everything new. Any ideas? Thanks.
 
Bad motor mount/trans mount has shown me the two and twist differently in reverse than in forward. So when idle and going forward no issue but when loading them the other way :
Possibly pinched fuel supply or return line?
Possibly tension on wires disconnecting a little?
Possibly shorting wires getting squished?

Can you do a couple videos of it?
 
Really? I’ve never noticed anything that we didn’t find an issue to.
Can someone do a video?
If electronic then I would definitely jump to a harness somewhere ot being happy.

Now I wanna snag up one or two of the 6.5 trucks at work today and go play with it on break time & lunch at work today to see if I notice any difference vs the dmax. We get issued the truck we use so I’m in an 08.

But it died? That ain't right… would keep me worried about reliability.
 
Thanks guys. Yea I am concerned about reliability. I forgot to mention it also hiccups once or twice after start up too before moving the truck. I do remember on the old motor the hiccups coincided with the wait to start light blinking.Seems to only act up before it warms up. I’ll get under her and inspect all of the wiring and grounds. The only thing not new is the PMD and harness. They were working fine before. Maybe harness pinched somewhere. I’ll also check for DTC. I’ll try to do a video. Like I said it happens so fast it’s just a hiccup
except when it died one time. I’ll report back. Thanks again guys.
 
when you did the install, did you remove the noise filter that connects between the harness and the optic sensor on top of the IP. it's the large square connector on the top of the IP. the noise filter was something GM installed from factory, looks like a short harness adapter with a rectangular black box in the middle. those things are known to give issues. if you remove it from the harness and connect the harness straight into the IP it might help.

I'm sure someone here has a picture of it.
 
Thanks guys, I ran through the wiring shaking them while engine running and checked codes. No dice.


Watch the tach two little blips. I’m convinced it’s happing only on first start up cold. Like I said on the old engine it coincided with the wait to start light blinking. The light is not workin now I still need to troubleshoot it. On the old engine I always thought the blip and WTS lamp was the GP firing because it was still cold and not burning the fuel correctly💁. It doesn’t have the optic sensor any more. New upper engine harness going to the IP from Quadstar. New ECT,s It use to do it on the old engine too. I have two working PMD,s. I can’t remember which one I ran on the old engine. Maybe I’ll switch to the other PMD. Maybe try another harness too. Since the harness was on the old engine. Sure hate too spend the money. I shook the hell out of the extension harness too😂. Maybe I’ll put a fuel psi gauge in cab to see what’s going on on cold start up. I have a new Raptor LP coming 😎. Sure hope it’s not the ECM🙏🏻. Thanks guys for helping me. I’ll report back.
 
Did your IP Timing and TDC Offsets get done after the install?

Try hooking up the scanner and get a read on the offset and with the parking brake set and wheels chocked, see what, if anything happens to IP Timing and Off Set when you shift into Reverse, and Or Drive.
 
Paveltolz said:
Did your IP Timing and TDC Offsets get done after the install?

Try hooking up the scanner and get a read on the offset and with the parking brake set and wheels chocked, see what, if anything happens to IP Timing and Off Set when you shift into Reverse, and Or Drive.
Click to expand...
Paveltolz said:
Did your IP Timing and TDC Offsets get done after the install?

Try hooking up the scanner and get a read on the offset and with the parking brake set and wheels chocked, see what, if anything happens to IP Timing and Off Set when you shift into Reverse, and Or Drive.
Click to expand...
Thanks Pav. I haven’t got to it yet. When I do what do I have to look at on the timing and offset numbers? If they change? The problem I have is I enter the truck data with the key on engine off then start it and the scanner disconnects and I have to re-enter the data after it is running. It happens so fast the event happens before I get done entering the data. Also sometimes it won’t do it in gear. In my previous post I stated I believed it only did it when cold. I was wrong it is also starting to do it after it’s warmed up after a start up. It’s so weird that it happens like clockwork in the morning and hit and miss the rest of the day. It seems to be happening more frequently and I’ll probably find out sooner than later. I just don’t want to get stuck somewhere lol😂
Will L. said:
Gonna need to set up a video camera on the clear ip return line looking for a one time burp of air.
Outside of that possibility (which I doubt now) that is in yonder electronicals of the ip/pmd/ignition power to them/ magical pixies are not happy.
Click to expand...
What do you think Will ? It’s hard to tell.
 
Goose57 said:
Thanks Pav. I haven’t got to it yet. When I do what do I have to look at on the timing and offset numbers? If they change? The problem I have is I enter the truck data with the key on engine off then start it and the scanner disconnects and I have to re-enter the data after it is running. It happens so fast the event happens before I get done entering the data. Also sometimes it won’t do it in gear. In my previous post I stated I believed it only did it when cold. I was wrong it is also starting to do it after it’s warmed up after a start up. It’s so weird that it happens like clockwork in the morning and hit and miss the rest of the day. It seems to be happening more frequently and I’ll probably find out sooner than later. I just don’t want to get stuck somewhere lol😂

What do you think Will ? It’s hard to tell.
Click to expand...
What's the known condition of the IP?
 
Hi all here are some more videos. One is of the clear return line and the other two are Tech 2 data and battery voltage on start up and when the event happens. Hope you can make it out. Still working on getting the WTS light to work. I wish I could narrow down the event of being a fuel or electrical issue. Maybe I’m overthinking thinking this because it did it on the old motor? Worried about long road trip reliability. Thanks guys.

 
You must log in or register to reply here.
Back
Top