• Welcome to The Truck Stop! We see you haven't REGISTERED yet.

    Your truck knowledge is missing!
    • Registration is FREE , all we need is your birthday and email. (We don't share ANY data with ANYONE)
    • We have tons of knowledge here for your diesel truck!
    • Post your own topics and reply to existing threads to help others out!
    • NO ADS! The site is fully functional and ad free!
    CLICK HERE TO REGISTER!

    Problems registering? Click here to contact us!

    Already registered, but need a PASSWORD RESET? CLICK HERE TO RESET YOUR PASSWORD!

Search results

  1. G

    Adding clear fuel lines for air in fuel line tests.

    Could be that IP OS filter, you don't need it. Do you know if you have an OBD1 or OBD2 system? Do you know where the PCM (computer) is? Should be inside the cab. Does it have PINK & BLUE or BROWN & BLUE connectors?
  2. G

    Glow plug wires under turbo

    That orange wire is special Teflon insulated and can handle the heat no problem.
  3. G

    Heater hose replacement

    part # 15986676 @ R.A.
  4. G

    1995 GMC 2500 4l80e put in my 2000 Chevy K2500 problems!

    If your transmission is in working order it will have reverse and 2nd gear when you unplug the main trans electrical connector on the drivers side. Either year PCM will control the 4L80, there are no differences as far as that is concerned.
  5. G

    3.8 liter, debris guard behind harmonic balancer.

    I googled this - seems to just pop off.
  6. G

    '95 Engine build

    Yes. I have never seen studs on the drivers side, but anything is possible.
  7. G

    '95 Engine build

    The stud goes in the first hole. The bracket goes on the 2nd hole with a bolt. That is how GM did it. I'm sure there must have been a purpose for the stud but I have not seen it. You will notice the bracket fits snug in the pan rail. That keeps it from twisting when you tighten the bolt.
  8. G

    '95 Engine build

    Second pan bolt, 1st bolt is a stud.
  9. G

    '95 Engine build

    The battery to starter cable is clamped there.
  10. G

    Need help identifying a bracket for intake

    My engine, not going anywhere. :cool:
  11. G

    Need help identifying a bracket for intake

    https://www.dieselplace.com/posts/9999179/
  12. G

    PASS LOCK SECURITY SYSTEM

    The resistor bypass only replaces the signal the passlock module wants. Passlock is still working. The SECURITY lamp will normally go out along with the WTS lamp. That should not cause any additional wait time. AK is correct, you can have the security turned off by a PCM reprogram. A 1997 PCM...
  13. G

    Need more bolt sizes

    That is just a bad drawing, the shield bolts to the starter brace bolt or stud on the block. The difference with that new shield in post #37 is the rear of the shield bolts directly to the stud that holds the transmission to the block. I don't remember seeing one like that but it is well...
  14. G

    Need more bolt sizes

    Might be this -
  15. G

    Crossover Pipe Bolts

    Here you go.
  16. G

    Need help identifying more brackets

    The long rod is the turbo brace, the short one goes from the hat to the turbo.
  17. G

    HVAC Fan wire plug

    Male conn is 12129155 term is 12084586 FM conn is 12129081 term is 12015858 The only reason for that conn. is so the main harness can be installed and removed without cutting any wires. Solder it together and forget it.
  18. G

    96 Suburban 6.5 Wiring Mystery for Lift Pump

    1996 and up (obd2) do not need the LP/OPS relay mod. The PCM controls the LP with the LP relay and the OPS is “redundant” per GM. With the key off and the LP running does unplugging the OPS shut it off?
  19. G

    What did you do with your GMT400 today...or yesterday....

    Daytime running lamps diode.
  20. G

    Exhaust manifold bolts

    https://www.wholesalegmpartsonline.com/showAssembly.aspx?ukey_assembly=431449&ukey_product=2547605#629
Back
Top