Search results

Ribs have been feeling better so yesterday I got the brake calipers replaced. Assembled tools and rachet straps etc. to go after that persnickety output shaft. Tried the technique in this video first (starts about the 1:04 min mark) to no avail. Regardless of rotation, angle, effort of...

Thanks. The Pads and Rotors were changed last fall and I had a run in issue then but, I’ll do another ‘run in’ session just for grins and giggles once its is back on the road.

New calipers arrived. Install was pretty straight forward. Sprung for powder coated units so had to remove some off one edge to get the clearance for them to fit. Other wise, no issues. Frau came out to work the brake pedal to complete bleeding process. Brake pedal is very firm now, even...

“He who dares, Wins!” Sometimes (mostly on my case) its a consolation prize though.

Decided to go after the front differential who’s driver’s side output shaft seal was damaged last summer when I suffered yet another C/V shaft issue. It’s been drip drip dripping ever since. I acquired a replacement front differential assy from a parts yard and have been waiting to get after...

Back from a great road trip last week and started in on house / car projects. Bruised or cracked two ribs…ouch. Pause everything. Week later, I went under the truck yesterday to work on a couple of issues. As for the calipers… Pulled the old one and, sure enough, there’s a lot of rust on the...

I’m just saying if the wires pass visual and tech. and are otherwise good but, the connectors are loose, repair or replace the connectors.

sorry for any confusion as I updated my post after I initially hit send. Repeating: In Yakima, “The best is PacTrans. Ask for Al or Bryan.”

@mannebk On Edit. In Yakima… The best is PacTrans. Ask for Al or Bryan.

Don’t know what status is as I finished the seal, got tackled by grandkids, packed the Atlas and left town without doing a test drive. I’ll let ya’ll know and I’ll pray the poor transfer case repair guy doesn’t get a surprise visit. Really appreciate the reminder though.

Finally decided to get the Output shaft seal replaced. No real issues and pretty straight forward. I viewed this guys YouTube vid to get familiarized with what the procedure should look like. The only hick up was the old seal was different than what I saw in the videos and the one I ordered...

I had my CDR and all plumbing connected for the test and, NO, the water will not get pulled all the way up the hose.

'Is this normal?' Yes. The old Heath Diesel page used to list a testing for blow by that involved visual checks at idle and vacuum pull at higher RPM (2500 IIRC). The aim was to not have people prematurely condemn their motors. I no longer have the document in digital or printed form (I...

Sounds like you got the wrong pads. Bad packaging? Just did the rear pads and rotors on Thing3's 2013 VW Jetta. Bracket bolts are the 'triple square' type. Torqued to about 1000lbs it seems. Used a breaker bar and floor jack to use the car's weight to break em loose. Confines are too tight to...

For me, its a 'while I'm in here' thing. I'd do the bolt mod because you don't know when you're going to either 'do things right' or one of those old plastic retainers is going to decide your next course of action for you. Bolts will cost you what 15 - 20 bucks? Cheap insurance and you can...

Bought a 19mm box end and cut out a portion and made my own line wrench 'for just such an emergency.'

@dbrannon79 I’m wondering if, in a failed attempt at logic, the 93 thinks it is exacting some sort of revenge for your wondering which truck to part out. Watch for the 95 to start running better to take advantage of the 93’ gullibility/naivety and failed sense of solidarity. I swear these...

I’m down for a road trip. I’m slated to do some traveling later this month/early next. I could actually pick it up either heading up to WA or, on the way back. I’m helping the FlatLiner Race Team Owner move to Kingman and driving one of the trucks. That schedule is driven by his current work...

Pull and inspect the heads. Retain for the 94 (just in case) or discard if questionable. You’d be able to see the condition of most of the cylinders. That’s going to be the question for potential recipients. Thinking that given your available time not being in MT now and construction starting...

My rear brakes need looking at too since its been 15 years… Understand about the Temp Gun. Shooting the outer edge (rust belt) of the rotor (dark meat). Honestly, the difference is only ~two degrees from the shiny side. Well within any of the gun’s margin of error Did a short test drive after...